SPL Performer s800 Stereo Power Amplifier Red

SPL Performer s800 Stereo Power Amplifier Black

SPL Performer s800 Stereo Power Amplifier Silver

SPL Performer s800 Stereo Power Amplifier

Name: SPL Performer s800 Stereo Power Amplifier
Brand: SPL
SKU: SPL.PERF.S800.RD
Price: 5099.0 AUD
Availability: InStock

SPL

Price:

$5,099

*Check with our team or your local store for availability.

We guarantee that all of our stock is 100% genuine,
Australian sourced stock, with full local warranty.

Share this product

Stereo Power Amplifier
This small stereo power amplifier shows everyone that size does not necessarily have anything to do with greatness. With the power of 570 W it has every speaker under control. Thanks to VOLTAiR technology, it is fast, precise and highly efficient with outstanding sound.

Better safe than sorry
The Performer s800 has a protection circuit against DC voltage and a limiter against output overload.

If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red.

To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds.

As one calls into the forest, so it echoes out.
This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode.

Trim to fit
With reference to the s800, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB.

This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier.

In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode.

Plus & Minus
The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm.

For bi-wiring operation, both types of connection can be used together.

No loudspeaker with less than 4 ohms impedance may be connected.

Bridge
You can turn the two power amplifier channels into one power amplifier by connecting only the two plus pole terminals to the loudspeaker. This allows 450W into 8 Ohm in mono operation mode.

AMP CTL
The power amplifier can be switched on and off using the AMP CTL connection between the Performer s800 and a preamplifier such as the Director Mk2 or the Crossover.

To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs.

Third-party preamps can also switch the Performer s800 on and off with their 12 V trigger.

Protection circuit against DC voltage
LDR limiter
Adjustable input sensitivity
Bridge both power amplifiers into one
AMP CTL connection

Analog Input & Thru: XLR (balanced)
Input gain (max)	32.5 dB
Input impedance (THRU not connected)	20 kΩ
Common mode rejection (THRU not connected)	-82 dB
Input sensitivity	6 dBu
Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug
Output power (RMS, 4 Ω)	570 W
Output power (RMS, 8 Ω)	370 W
Harmonic distortion (1 kHz, 8 Ω)	< 0.03 %
Output power (RMS, 8 Ω, Bridge Mode)	450 W
Harmonic distortion (1 kHz, 8 Ω, Bridge Mode)	< 0.011 %
Output power (peak to peak)	74 V
Output power (peak to peak, Bridge Mode)	180 V
Output voltage (RMS)	35 V
Output voltage (RMS, Bridge Mode)	86 V
Output impedance (20 Hz – 20 kHz)	< 0.031 Ω
Output impedance (20 Hz – 20 kHz, Bridge Mode)	< 0.043 Ω
Amplification gain	26 dB
Amplification gain (Bridge Mode)	32 dB
Damping factor (1 kHz, 8 Ohm)	> 300
Damping factor (1 kHz, 8 Ohm, Bridge Mode)	> 190
Frequency range (-3dB)	9 Hz – 200 kHz
Noise (A-weighted)	-123 dBu
Internal Linear Power Supply with Shielded Toroidal Transformer
Toroidal transformer	875 VA
Operating voltage (Input stage)	+/- 60 V
Operating voltage (power stage)	+/- 60 V
Operating voltage for relays, LEDs, AMP CTL	+ 12 V
Mains Power Supply
Mains voltage (selectable, see fuse chamber)	230 V AC / 50; 115 V AC / 60 Hz
Fuse for 230 V	T 4 mA
Fuse for 115 V	T 8 A
Power consumption	max. 875 VA
Idle power consumption	40 W
Stand-by power consumption	< 0,3 W
Dimensions & Weight
W x H x D (width x height incl. feet x depth)	278 x 100 x 375 mm
Unit weight	12.8 kg
Shipping weight	14 kg

SPL Performer s800 Stereo Power Amplifier

SPL Performer s800 Amplifier User Manual

Recover password

Create my account

SPL Performer s800 Stereo Power Amplifier

Description

Analog Input & Thru: XLR (balanced)

Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug

Internal Linear Power Supply with Shielded Toroidal Transformer

Mains Power Supply

Dimensions & Weight

Customer Reviews

In the same category

Recently viewed